ifindbombs
New Member
2017 RC 390
Long story short, I installed a PCV with WB2, K&N air filter with MT open air lid, straight mid pipe, cheap slip on with out baffle, and map from Rottweiler for open air box and comp exhaust.
Bike will not stay running at idle, and struggles on all gears unless I’m wide open in 5th or 6th. Acts like it wants to stall.
I have a code reader hooked up and it threw all of these codes this morning on a 10 minutes ride. I know I could take it to a ktm shop and have them fix it, but I would like to learn more about the bike and do it myself. I’m just not sure where to start. I did do some research and found that that TAC code could be caused by a dirty throttle body. Could that cause everything else, or do I have some other serious issues? Any advice on where to start my trouble shooting would be greatly appreciated.
OBD codes:
Car Scanner ELM OBD2
DTC report
Selected brand: [ OTHER BRAND ]
VIN: MD2JYJ406HC270674
============1==============
P061F(00)
Raw code: 061F00
ECU: Engine control unit
Status: Pending, Confirmed, Test failed since last DTC clear, Warning indicator requested
OBDII: Engine control module (ECM), throttle actuator controller - performance problem
============2==============
P0134(00)
Raw code: 013400
ECU: Engine control unit
Status: Confirmed, Test failed since last DTC clear, Warning indicator requested
OBDII: Heated oxygen sensor (HO2S) 1, bank 1 - no activity detected
============3==============
P0130(00)
Raw code: 013000
ECU: Engine control unit
Status: Confirmed, Test failed since last DTC clear, Warning indicator requested
OBDII: Heated oxygen sensor (HO2S) 1, bank 1 - circuit malfunction
============4==============
P2176(00)
Raw code: 217600
ECU: Engine control unit
Status: Confirmed, Test failed since last DTC clear, Test not completed during this operation cycle, Warning indicator requested
OBDII: Throttle actuator control (TAC) system - idle position not learned
============5==============
P2135(00)
Raw code: 213500
ECU: Engine control unit
Status: Test failed, Test failed (current drive cycle), Pending, Confirmed, Test failed since last DTC clear, Warning indicator requested
OBDII: Throttle position (TP) or Accelerator pedal position (APP) sensor/switch A/B - voltage correlation
============6==============
P2135
Raw code: 2135
ECU: Engine control unit
Status: Pending
OBDII: Throttle position (TP) or Accelerator pedal position (APP) sensor/switch A/B - voltage correlation
============7==============
P061F
Raw code: 061F
ECU: Engine control unit
Status: Pending
OBDII: Engine control module (ECM), throttle actuator controller - performance problem
============8==============
P2135
Raw code: 2135
ECU: Engine control unit
Status: Confirmed
OBDII: Throttle position (TP) or Accelerator pedal position (APP) sensor/switch A/B - voltage correlation
============9==============
P061F
Raw code: 061F
ECU: Engine control unit
Status: Confirmed
OBDII: Engine control module (ECM), throttle actuator controller - performance problem
============10==============
P0134
Raw code: 0134
ECU: Engine control unit
Status: Confirmed
OBDII: Heated oxygen sensor (HO2S) 1, bank 1 - no activity detected
============11==============
P0130
Raw code: 0130
ECU: Engine control unit
Status: Confirmed
OBDII: Heated oxygen sensor (HO2S) 1, bank 1 - circuit malfunction
============12==============
P2176
Raw code: 2176
ECU: Engine control unit
Status: Confirmed
OBDII: Throttle actuator control (TAC) system - idle position not learned
Thanks again in advance!
Long story short, I installed a PCV with WB2, K&N air filter with MT open air lid, straight mid pipe, cheap slip on with out baffle, and map from Rottweiler for open air box and comp exhaust.
Bike will not stay running at idle, and struggles on all gears unless I’m wide open in 5th or 6th. Acts like it wants to stall.
I have a code reader hooked up and it threw all of these codes this morning on a 10 minutes ride. I know I could take it to a ktm shop and have them fix it, but I would like to learn more about the bike and do it myself. I’m just not sure where to start. I did do some research and found that that TAC code could be caused by a dirty throttle body. Could that cause everything else, or do I have some other serious issues? Any advice on where to start my trouble shooting would be greatly appreciated.
OBD codes:
Car Scanner ELM OBD2
DTC report
Selected brand: [ OTHER BRAND ]
VIN: MD2JYJ406HC270674
============1==============
P061F(00)
Raw code: 061F00
ECU: Engine control unit
Status: Pending, Confirmed, Test failed since last DTC clear, Warning indicator requested
OBDII: Engine control module (ECM), throttle actuator controller - performance problem
============2==============
P0134(00)
Raw code: 013400
ECU: Engine control unit
Status: Confirmed, Test failed since last DTC clear, Warning indicator requested
OBDII: Heated oxygen sensor (HO2S) 1, bank 1 - no activity detected
============3==============
P0130(00)
Raw code: 013000
ECU: Engine control unit
Status: Confirmed, Test failed since last DTC clear, Warning indicator requested
OBDII: Heated oxygen sensor (HO2S) 1, bank 1 - circuit malfunction
============4==============
P2176(00)
Raw code: 217600
ECU: Engine control unit
Status: Confirmed, Test failed since last DTC clear, Test not completed during this operation cycle, Warning indicator requested
OBDII: Throttle actuator control (TAC) system - idle position not learned
============5==============
P2135(00)
Raw code: 213500
ECU: Engine control unit
Status: Test failed, Test failed (current drive cycle), Pending, Confirmed, Test failed since last DTC clear, Warning indicator requested
OBDII: Throttle position (TP) or Accelerator pedal position (APP) sensor/switch A/B - voltage correlation
============6==============
P2135
Raw code: 2135
ECU: Engine control unit
Status: Pending
OBDII: Throttle position (TP) or Accelerator pedal position (APP) sensor/switch A/B - voltage correlation
============7==============
P061F
Raw code: 061F
ECU: Engine control unit
Status: Pending
OBDII: Engine control module (ECM), throttle actuator controller - performance problem
============8==============
P2135
Raw code: 2135
ECU: Engine control unit
Status: Confirmed
OBDII: Throttle position (TP) or Accelerator pedal position (APP) sensor/switch A/B - voltage correlation
============9==============
P061F
Raw code: 061F
ECU: Engine control unit
Status: Confirmed
OBDII: Engine control module (ECM), throttle actuator controller - performance problem
============10==============
P0134
Raw code: 0134
ECU: Engine control unit
Status: Confirmed
OBDII: Heated oxygen sensor (HO2S) 1, bank 1 - no activity detected
============11==============
P0130
Raw code: 0130
ECU: Engine control unit
Status: Confirmed
OBDII: Heated oxygen sensor (HO2S) 1, bank 1 - circuit malfunction
============12==============
P2176
Raw code: 2176
ECU: Engine control unit
Status: Confirmed
OBDII: Throttle actuator control (TAC) system - idle position not learned
Thanks again in advance!
Last edited: