Hi Guys, anybody tried to disconnect or bypass their roll over sensor on their RC390? Or runs without the sensor plugged in?
Our race bike stalls every time it goes thru a full leaned high-speed corners reaching more than 63 degrees lean angle.
I am trying to install a gear indicator with shift light which is much bigger and easier to see than the stock dash.
I have removed ABS so I do not have the front speed sensor anymore, however, I did keep the rear speed sensor since Bazzaz needs it. The rear speed sensor has 2 wires, and it...
I'd appreciate your comments, please. My 2015 RC is a road bike, standard intake/exhaust so far. In general I would like an A/F gauge to keep an eye out for changes and to avoid risk of lean detonation/excess fuel washing oil off the bore, especially after fitting a custom airbox I am working...
Good day everyone.
I'm trying to install the shift light pro on my RC390.
I think I found where the crank position sensor connector is.
But I'm not sure which wire is the right one which transmit the rpm.
Is it the green wire or black/yellow wire?
Could anyone let me know or take a photo to...
I'm in need of a spare Throttle Position Sensor for a 2015 RC 390.(#90141070000) I'm looking to make it adjustable and would like to get one as a spare in case things dont work
the way I want them to....has anyone here tried to do this yet?....looks to be pretty straight forward to modify to get...
Hey guys this is my first post here .I was thinking of making a Quick Shifter for my bike using a pressure sensor and the widely used micro controller Arduino uno .The pressure sensor will be attached to the gear lever .This is how i want it to work ,When the pressure sensor on the gear lever...
Any fellow racers figure out another option to the side stand delete without the cup removal sensor. :In canada the part is not available and to get it shipped from commonwealth costs me 2x what the sensor is worth. I may just saftey wire the sensor in place in the side-stand up position for...
Has anyone installed the AutoTune for PowerCommander V on their RC 390?
Is the PCV w/ AT-200 the correct kit?
Looking for more information on the installation procedures for the AutoTune on this bike.
Does the O2 sensor need drilling/welding or is it a stock fit?
Anybody know if it is possible to connect the speed input of the PCV to the rear wheel sensor?
If so what wire is used for the signal?
I tried both wires going to the sensor.
.
So now that the PCV is installed. it was time to install the Dyno Jet Wideband Commander 2 ( WBC2 or WB2) p.n. 15-7023x........ so we could have more Control over the Fuel map on the bike.
As many of you know the KTM 390 has a difficult ECU that doesn't allow closed loop to be altered...
a/f
autotune
band
bike
closed
commander
conjunction
control
ecu
fuel
ktm 390 wb2 installation
loop
low
map
output
pcv
power
ratio
sensor
voltage
wb2
wbc2
wide
wideband
wire
Hi guys!
To improve my skills on track, I need help.
But coaching is too expensive for my bank account...
So I found this tool to save a little bit my money... :
https://www.kickstarter.com/projects/riders-enovation/3dms-pour-motard-mesurez-ameliorez-and-partagez-vo/rewards
I think...
Mine is sending codes, I gotta get to it..or find it first. Anyone happen to know of it's location? I know it attached (through the wiring diagram) to the EFI control unit but before I start really digging into it I was wondering if someone may have known it's location.
Thanks!
Hey guys , mil light is flashing . 2 blinks then 3 quicker ones . Guessing fault code 23 ?????
I think its the o2 sensor ( lambda sensor ) was massivly over fueling last track session . No drop in performance but used 1/2 a litre more fuel per session and my rear swing arm looks like its...